Sulfanilamide SDS/MSDS (Safety Data Sheet)

3.1 Substances
Product name: Sulfanilamide
CAS Number: 63-74-1
PubChem CID: 5333
Molecular formula: C6H8N2O2S
Molecular weight: 172.21 g/mol
IUPAC name: 4-aminobenzenesulfonamide

3.2 Mixtures
Not applicable (pure substance).

4.1 Description of first aid measures
Inhalation: INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to t
Skin contact: SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
Eye contact: EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
Ingestion: INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport

4.2 Most important symptoms and effects, both acute and delayed
See Section 11 (Toxicological Information).

4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically. Contact a poison control center or physician for severe exposure.

5.1 Extinguishing media
Suitable: Water spray, dry chemical, carbon dioxide (CO2), alcohol-resistant foam.
Unsuitable: None known.

5.2 Specific hazards arising from the substance or mixture
Fires involving this compound can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. (NTP, 1992)

5.3 Advice for firefighters
Wear self-contained breathing apparatus (SCBA) and full protective clothing.
Fight fire from upwind. Cool containers with water spray until fire is extinguished.

6.1 Personal precautions, protective equipment and emergency procedures
Wear appropriate personal protective equipment (see Section 8).
Avoid breathing dust/vapor. Ensure adequate ventilation.
Evacuate personnel to safe areas. Keep people away from and upwind of spill.

6.2 Environmental precautions
Prevent product from entering drains, waterways, or soil.
Contain spill with inert absorbent material.

6.3 Methods and materials for containment and cleaning up
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.
FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)
SRP: At the time of review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices.

7.1 Precautions for safe handling
SMALL SPILLS AND LEAKAGE: Should a spill occur while you are handling this chemical, you should dampen the solid spill material with acetone, then transfer the dampened material to a suitable container. Use absorbent paper dampened with acetone to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with acetone followed by washing with a strong soap and water solution. Do not reenter the contaminate area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONS: You should protect this container from exposure to light. Keep the container tightly closed under an inert atmosphere and store under refrigerated temperatures. (NTP, 1992)

7.2 Conditions for safe storage, including any incompatibilities
Store in a cool, dry, well-ventilated area. Keep container tightly closed.
Store away from incompatible materials (see Section 10).
Protect from light and moisture.
Recommended storage (industry convention for research compounds): -20°C for long-term storage; 2-8°C for short-term use and transport.
[Note: This is a general industry recommendation. Always verify exact storage conditions with the supplier Certificate of Analysis (COA).]

9.1 Information on basic physical and chemical properties
a) Appearance: Sulfanilamide is a white powder. pH of 0.5% aqueous solution: 5.8-6.1. (NTP, 1992)
b) Odor: No data available
c) Odor threshold: No data available
d) pH: NEUTRAL TO LITMUS; PH OF 0.5% AQ SOLN: 5.8-6.1
e) Melting point/freezing point: 329 to 331 °F (NTP, 1992)
f) Initial boiling point and boiling range: No data available
g) Flash point: No data available
h) Evaporation rate: No data available
i) Flammability (solid, gas): No data available
j) Upper/lower flammability or explosive limits: No data available
k) Vapor pressure: 0.0000073 [mmHg]
l) Vapor density: No data available
m) Relative density: 1.08 at 68 °F (NTP, 1992) - Denser than water; will sink
n) Water solubility: 0.1 to 1.0 mg/mL at 72 °F (NTP, 1992)
o) Partition coefficient: n-octanol/water: Log P (n-octanol/water): -0.6
p) Auto-ignition temperature: No data available
q) Decomposition temperature: No data available
r) Viscosity: No data available
s) Explosive properties: No data available
t) Oxidizing properties: No data available

9.2 Other information
Topological Polar Surface Area (TPSA): 94.6 Ų
Complexity: 211

11.1 Information on toxicological effects
Acute toxicity:
No acute toxicity data available.
Skin corrosion/irritation:
Causes skin irritation (H315).
Serious eye damage/eye irritation:
Causes serious eye irritation (H319).
Respiratory or skin sensitization:
No data available.
Germ cell mutagenicity:
No data available.
Carcinogenicity:
No data available.
Reproductive toxicity:
No data available.
Specific target organ toxicity (single exposure):
No data available.
Specific target organ toxicity (repeated exposure):
No data available.
Aspiration hazard:
No data available.

11.2 Additional information
No additional toxicological information available.

12.1 Toxicity
Sulfanilamide's production and use as an antibacterial and an antimicrobial agent may result in its release to the environment through various waste streams. Sulfanilamide has been detected in groundwater near a landfill. If released to soil, sulfanilamide should have very high mobility. However, the adsorptivity of sulfanilamide is expected to be sensitive to pH since sulfanilamide has a pKa of 10.58. Also, studies have shown that covalent binding of ring-substituted anilines, such as sulfanilamide, to humates involves a reversible equilibrium which is followed by a very slow and relatively irreversible reaction which may reduce sulfanilamide's mobility in soil. Volatilization of sulfanilamide should not be important from moist or dry soil surfaces. Sulfanilamide may be susceptible to direct photolysis on soil surfaces based on its absorption of light at wavelengths >290 nm. If released to water, sulfanilamide should not adsorb to suspended solids and sediment. Sulfanilamide will be essentially non-volatile from water surfaces. An estimated BCF value of 0.2 suggests that sulfanilamide will not bioconcentrate in aquatic organisms. Although aniline was able to degrade quickly, sulfanilamide degraded very slowly by aniline-acclimated activated sludge in a 200 hour Warburg Run, suggesting that biodegradation in water and soil will be slow. If released to the atmosphere, sulfanilamide will exist in both the vapor and particulate phases in the ambient atmosphere. Vapor-phase sulfa

12.2 Persistence and degradability
No data available.

12.3 Bioaccumulative potential
Log P (n-octanol/water): -0.6
Low potential for bioaccumulation (Log P < 3).

12.4 Mobility in soil
No data available.

12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available.

12.6 Other adverse effects
No other adverse ecological effects identified.

13.1 Waste treatment methods
Waste Treatment Methods: Waste material must be disposed of in accordance with national and local regulations. Leave chemicals in original containers and do not mix with other waste. Handle uncleaned containers in the same manner as the product itself.

14.1 UN number
Not regulated as dangerous goods (research quantities typically exempt).

14.2 UN proper shipping name
Not subject to transport regulations (small quantities for research use).

14.3 Transport hazard class(es)
Not classified as dangerous goods for transport (research quantities).
DOT label: Corrosive

14.4 Packing group
Not applicable (not regulated as dangerous goods in typical research quantities).

14.5 Environmental hazards
Marine pollutant: No (not classified as environmentally hazardous per GHS).

14.6 Special precautions for user
Transport in original packaging. Ensure containers are tightly sealed.
For bulk or commercial quantities, consult applicable transport regulations (DOT, IATA, IMDG).

14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable.

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
US EPA / TSCA: Subject to EPA TSCA regulations
EU ECHA / REACH: Registered (REACH Active)

SARA 302 Components:
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313 Components:
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SARA 311/312 Hazards:
Acute (short-term) health hazard

Massachusetts Right To Know Components:
This material contains components subject to the Massachusetts Right to Know Act. See Section 2 for hazard classification.
Pennsylvania Right To Know Components:
This material contains components subject to the Pennsylvania Right to Know Act. See Section 2 for hazard classification.
New Jersey Right To Know Components:
This material contains components subject to the New Jersey Right to Know Act. See Section 2 for hazard classification.

California Prop. 65 Components:
This product does not contain any chemicals known to the State of California to cause cancer, birth defects, or any other reproductive harm.

Other regulatory listings:
- The Australian Inventory of Industrial Chemicals: Chemical: Benzenesulfonamide, 4-amino-
- EFSA Legal Basis: Regulation (EC) No 1107/2009 (amended)
- FDA Requirements: Manufacturers, packers, and distributors of drug and drug products for human use are responsible for complying with the labeling, certification, and usage requirements as prescribed by the Federal Food, Drug, and Cosmetic Act, as amended (secs 201-902, 52 Stat. 1040 et seq., as amended; 21 U.S.C. 32

15.2 Chemical safety assessment
A chemical safety assessment has not been carried out for this substance.
For research-use-only compounds, no CSA is required under REACH Annex I.

Revision Date: 2026/09/08
Further Information: The information provided is believed to be correct but is not exhaustive and should be used only as a guideline based on current knowledge. It does not represent a guarantee of the properties of the product. Selleck Chemicals Corporation and its Affiliates shall not be held liable for any damage resulting from handling or contact with the product.