Propylparaben SDS/MSDS (Safety Data Sheet)

3.1 Substances
Product name: Propylparaben
CAS Number: 94-13-3
PubChem CID: 7175
Molecular formula: C10H12O3
Molecular weight: 180.20 g/mol
IUPAC name: propyl 4-hydroxybenzoate

3.2 Mixtures
Not applicable (pure substance).

4.1 Description of first aid measures
Inhalation: INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to t
Skin contact: SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
Eye contact: EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
Ingestion: INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport

4.2 Most important symptoms and effects, both acute and delayed
See Section 11 (Toxicological Information).

4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically. Contact a poison control center or physician for severe exposure.

5.1 Extinguishing media
Suitable: Water spray, dry chemical, carbon dioxide (CO2), alcohol-resistant foam.
Unsuitable: None known.

5.2 Specific hazards arising from the substance or mixture
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. A water spray may also be used. (NTP, 1992)
Suitable extinguishing media: Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Advice for firefighters: Wear self-contained breathing apparatus for firefighting if necessary.

5.3 Advice for firefighters
Wear self-contained breathing apparatus (SCBA) and full protective clothing.
Fight fire from upwind. Cool containers with water spray until fire is extinguished.

6.1 Personal precautions, protective equipment and emergency procedures
Wear appropriate personal protective equipment (see Section 8).
Avoid breathing dust/vapor. Ensure adequate ventilation.
Evacuate personnel to safe areas. Keep people away from and upwind of spill.

6.2 Environmental precautions
Prevent product from entering drains, waterways, or soil.
Contain spill with inert absorbent material.

6.3 Methods and materials for containment and cleaning up
ACCIDENTAL RELEASE MEASURES: Personal precautions, protective equipment and emergency procedures: Avoid dust formation. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Environmental precautions: Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided. Methods and materials for containment and cleaning up: Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal.
SRP: Recycle any unused portion of the material for its approved use or return it to the manufacturer or supplier. Ultimate disposal of the chemical must consider: the material's impact on air quality; potential migration in air, soil or water; effects on animal, aquatic and plant life; and conformance with environmental and public health regulations. If it is possible or reasonable use an alternative chemical product with less inherent propensity for occupational harm/injury/toxicity or environmental contamination.
Product: Offer surplus and non-recyclable solutions to a licensed disposal company; Contaminated packaging: Dispose of as unused product.
ACCIDENTAL RELEASE MEASURES: Personal precautions, protective equipment and emergency procedures: Avoid dust formation. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Environmental precautions: Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided.
Precautions for safe handling: Further processing of solid materials may result in the formation of combustible dusts. The potential for combustible dust formation should be taken into consideration before additional processing occurs. Provide appropriate exhaust ventilation at places where dust is formed.
Appropriate engineering controls: Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
For more Preventive Measures (Complete) data for PROPYLPARABEN (8 total), please visit the HSDB record page.

7.1 Precautions for safe handling
SMALL SPILLS AND LEAKAGE: Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONS: You should store this material under ambient temperatures. (NTP, 1992)
Keep container tightly closed in a dry and well-ventilated place.
Containers should be stored in a dry place & kept tightly sealed when not in use. /Parabens/

7.2 Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place.
Containers should be stored in a dry place & kept tightly sealed when not in use. /Parabens/
Store away from incompatible materials (see Section 10).
[Note: Specific storage temperature not available in public databases. Refer to supplier Certificate of Analysis (COA) for exact storage conditions.]

9.1 Information on basic physical and chemical properties
a) Appearance: Propyl-4-hydroxybenzoate appears as colorless crystals or white powder or chunky white solid. Melting point 95-98 °C. Odorless or faint aromatic odor. Low toxicity, Tasteless (numbs the tongue). pH: 6.5-7.0 (slightly acidic) in solution.
b) Odor: Odorless or has faint odor
c) Odor threshold: No data available
d) pH: No data available
e) Melting point/freezing point: 203 to 208 °F (NTP, 1992)
f) Initial boiling point and boiling range: 271 °F at 1 mmHg (NTP, 1992)
g) Flash point: No data available
h) Evaporation rate: No data available
i) Flammability (solid, gas): No data available
j) Upper/lower flammability or explosive limits: No data available
k) Vapor pressure: 0.000555 [mmHg]
l) Vapor density: No data available
m) Relative density: 1.28 at 77 °F (NTP, 1992) - Denser than water; will sink
n) Water solubility: less than 1 mg/mL at 54 °F (NTP, 1992)
o) Partition coefficient: n-octanol/water: Log P (n-octanol/water): 3
p) Auto-ignition temperature: No data available
q) Decomposition temperature: No data available
r) Viscosity: No data available
s) Explosive properties: No data available
t) Oxidizing properties: No data available

9.2 Other information
Topological Polar Surface Area (TPSA): 46.5 Ų
Complexity: 160

11.1 Information on toxicological effects
Acute toxicity:
No acute toxicity data available.
Skin corrosion/irritation:
Causes skin irritation (H315).
Serious eye damage/eye irritation:
Causes serious eye irritation (H319).
Respiratory or skin sensitization:
May cause an allergic skin reaction (H317).
Germ cell mutagenicity:
No data available.
Carcinogenicity:
No data available.
Reproductive toxicity:
No data available.
Specific target organ toxicity (single exposure):
H370, H373
Specific target organ toxicity (repeated exposure):
No data available.
Aspiration hazard:
No data available.

11.2 Additional information
Carcinogen classification:
No indication of carcinogenicity to humans (not listed by IARC).
Data source: Hazardous Substances Data Bank (HSDB) via PubChem.

12.1 Toxicity
EC50; Species: Daphnia magna (Water flea); Conditions: freshwater, static, pH 7.6-7.7, dissolved oxygen 100% saturated; Concentration: 27500 ug/L for 24 hr (95% confidence interval: 20300-45800 ug/L); Effect: intoxication, immobilization /formulation/
EC50; Species: Daphnia magna (Water flea); Conditions: freshwater, static, pH 7.6-7.7, dissolved oxygen 100% saturated; Concentration: 15400 ug/L for 48 hr (95% confidence interval: 7970-32300 ug/L); Effect: intoxication, immobilization /formulation/
LC50; Species: Dugesia japonica (Flatworm) body length 0.7 cm; Conditions: freshwater, static, 25 °C; Concentration: 14700 ug/L for 24 hr (95% confidence interval: 13100-15100 ug/L) />99% purity/
LC50; Species: Dugesia japonica (Flatworm) body length 0.7 cm; Conditions: freshwater, static, 25 °C; Concentration: 12300 ug/L for 96 hr (95% confidence interval: 13100-15100 ug/L) />99% purity/
/AQUATIC SPECIES/ The estrogenic effect of propylparaben was investigated in a rainbow trout Oncorhynchus mykiss test system. Propylparaben was administered orally to sexually immature rainbow trout every second day for up to 10 days in doses between 7 and 1830 mg/kg/2 days and in the water at 50 and 225 ug/L for 12 days. Plasma vitellogenin was measured before and during the exposures and the concentrations of propylparaben in liver and muscle were determined at the end of experiments. Increases in average plasma vitellogenin levels were seen at oral exposure to 33 mg propylparaben/kg/2 days; the

12.2 Persistence and degradability
No data available.

12.3 Bioaccumulative potential
Log P (n-octanol/water): 3
Low potential for bioaccumulation (Log P < 3).

12.4 Mobility in soil
No data available.

12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available.

12.6 Other adverse effects
This substance is classified as hazardous to the aquatic environment.

13.1 Waste treatment methods
Waste Treatment Methods: Waste material must be disposed of in accordance with national and local regulations. Leave chemicals in original containers and do not mix with other waste. Handle uncleaned containers in the same manner as the product itself.

14.1 UN number
Not regulated as dangerous goods (research quantities typically exempt).

14.2 UN proper shipping name
Not subject to transport regulations (small quantities for research use).

14.3 Transport hazard class(es)
Not classified as dangerous goods for transport (research quantities).

14.4 Packing group
Not applicable (not regulated as dangerous goods in typical research quantities).

14.5 Environmental hazards
Marine pollutant: Yes (classified as environmentally hazardous per GHS).

14.6 Special precautions for user
Transport in original packaging. Ensure containers are tightly sealed.
For bulk or commercial quantities, consult applicable transport regulations (DOT, IATA, IMDG).

14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable.

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
US EPA / TSCA: Subject to EPA TSCA regulations
EU ECHA / REACH: Registered (REACH Active)

SARA 302 Components:
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313 Components:
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SARA 311/312 Hazards:
Acute (short-term) health hazard
Chronic (long-term) health hazard
Environmental hazard

Massachusetts Right To Know Components:
This material contains components subject to the Massachusetts Right to Know Act. See Section 2 for hazard classification.
Pennsylvania Right To Know Components:
This material contains components subject to the Pennsylvania Right to Know Act. See Section 2 for hazard classification.
New Jersey Right To Know Components:
This material contains components subject to the New Jersey Right to Know Act. See Section 2 for hazard classification.

California Prop. 65 Components:
This product does not contain any chemicals known to the State of California to cause cancer, birth defects, or any other reproductive harm.

Other regulatory listings:
- The Australian Inventory of Industrial Chemicals: Chemical: Benzoic acid, 4-hydroxy-, propyl ester
- California Safe Cosmetics Program (CSCP) Reportable Ingredient: Hazard Traits - Endocrine Toxicity; Reproductive Toxicity Authoritative List - CECBP - Priority Chemicals Report - if used as a fragrance or flavor ingredient
- EFSA Legal Basis: Directive (EC) No 114/2003
- FIFRA Requirements: Residues of propyl p-hydroxybenzoate are exempted from the requirement of a tolerance when used as a preservative for formulations in accordance with good agricultural practice as inert (or occasionally active) ingredients in pesticide formulations applied to growing crops or to raw agricultural com
- FDA Requirements: Propylparaben is a food additive permitted for direct addition to food for human consumption as a synthetic flavoring substance and adjuvant in accordance with the following conditions: a) they are used in the minimum quantity required to produce their intended effect, and otherwise in accordance wi

15.2 Chemical safety assessment
A chemical safety assessment has not been carried out for this substance.
For research-use-only compounds, no CSA is required under REACH Annex I.

Revision Date: 2026/09/09
Further Information: The information provided is believed to be correct but is not exhaustive and should be used only as a guideline based on current knowledge. It does not represent a guarantee of the properties of the product. Selleck Chemicals Corporation and its Affiliates shall not be held liable for any damage resulting from handling or contact with the product.