Oxybenzone SDS/MSDS (Safety Data Sheet)

3.1 Substances
Product name: Oxybenzone
CAS Number: 131-57-7
PubChem CID: 4632
Molecular formula: C14H12O3
Molecular weight: 228.24 g/mol
IUPAC name: (2-hydroxy-4-methoxyphenyl)-phenylmethanone

3.2 Mixtures
Not applicable (pure substance).

4.1 Description of first aid measures
Inhalation: INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to t
Skin contact: SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
Eye contact: EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
Ingestion: INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport

4.2 Most important symptoms and effects, both acute and delayed
See Section 11 (Toxicological Information).

4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically. Contact a poison control center or physician for severe exposure.

5.1 Extinguishing media
Suitable: Water spray, dry chemical, carbon dioxide (CO2), alcohol-resistant foam.
Unsuitable: None known.

5.2 Specific hazards arising from the substance or mixture
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. (NTP, 1992)
Suitable extinguishing media: Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Advice for firefighters: Wear self contained breathing apparatus for fire fighting if necessary.

5.3 Advice for firefighters
Wear self-contained breathing apparatus (SCBA) and full protective clothing.
Fight fire from upwind. Cool containers with water spray until fire is extinguished.
Flash point: 100 °C (212 °F) - closed cup

6.1 Personal precautions, protective equipment and emergency procedures
Wear appropriate personal protective equipment (see Section 8).
Avoid breathing dust/vapor. Ensure adequate ventilation.
Evacuate personnel to safe areas. Keep people away from and upwind of spill.

6.2 Environmental precautions
Prevent product from entering drains, waterways, or soil.
Contain spill with inert absorbent material.

6.3 Methods and materials for containment and cleaning up
ACCIDENTAL RELEASE MEASURES: Personal precautions, protective equipment and emergency procedures: Use personal protective equipment. Avoid dust formation. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust. Environmental precautions: Do not let product enter drains. Methods and materials for containment and cleaning up: Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal.
SRP: Recycle any unused portion of the material for its approved use or return it to the manufacturer or supplier. Ultimate disposal of the chemical must consider: the material's impact on air quality; potential migration in air, soil or water; effects on animal, aquatic and plant life; and conformance with environmental and public health regulations. If it is possible or reasonable use an alternative chemical product with less inherent propensity for occupational harm/injury/toxicity or environmental contamination.
Product: Offer surplus and non-recyclable solutions to a licensed disposal company. Contact a licensed professional waste disposal service to dispose of this material; Contaminated packaging: Dispose of as unused product.
ACCIDENTAL RELEASE MEASURES: Personal precautions, protective equipment and emergency procedures: Use personal protective equipment. Avoid dust formation. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust. Environmental precautions: Do not let product enter drains.
Precautions for safe handling: Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Provide appropriate exhaust ventilation at places where dust is formed. Normal measures for preventive fire protection.
Appropriate engineering controls: Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
For more Preventive Measures (Complete) data for 2-Hydroxy-4-methoxybenzophenone (6 total), please visit the HSDB record page.

7.1 Precautions for safe handling
SMALL SPILLS AND LEAKAGE: Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONS: You should protect this chemical from exposure to light. Keep the container tightly closed under an inert atmosphere, and store under refrigerated temperatures. (NTP, 1992)
Keep container tightly closed in a dry and well-ventilated place.
Store below 40 °C (104 °F), preferably between 15 and 30 deg. C (59 and 86 deg. F), unless otherwise specified by manufacturer. /Sunscreen agents, topical/

7.2 Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place.
Store below 40 °C (104 °F), preferably between 15 and 30 deg. C (59 and 86 deg. F), unless otherwise specified by manufacturer. /Sunscreen agents, topical/
Store away from incompatible materials (see Section 10).
[Note: Specific storage temperature not available in public databases. Refer to supplier Certificate of Analysis (COA) for exact storage conditions.]

9.1 Information on basic physical and chemical properties
a) Appearance: 2-hydroxy-4-methoxybenzophenone appears as white to off-white or light yellow powder. (NTP, 1992)
b) Odor: Weak odor
c) Odor threshold: No data available
d) pH: No data available
e) Melting point/freezing point: 151 °F (NTP, 1992)
f) Initial boiling point and boiling range: 302 to 320 °F at 5 mmHg (NTP, 1992)
g) Flash point: 100 °C (212 °F) - closed cup
h) Evaporation rate: No data available
i) Flammability (solid, gas): No data available
j) Upper/lower flammability or explosive limits: No data available
k) Vapor pressure: 0.00000142 [mmHg]
l) Vapor density: No data available
m) Relative density: 1.32 at 25 °C
n) Water solubility: less than 1 mg/mL at 68 °F (NTP, 1992)
o) Partition coefficient: n-octanol/water: Log P (n-octanol/water): 3.6
p) Auto-ignition temperature: No data available
q) Decomposition temperature: No data available
r) Viscosity: No data available
s) Explosive properties: No data available
t) Oxidizing properties: No data available

9.2 Other information
Topological Polar Surface Area (TPSA): 46.5 Ų
Complexity: 258

11.1 Information on toxicological effects
Acute toxicity:
No acute toxicity data available.
Skin corrosion/irritation:
Causes skin irritation (H315).
Serious eye damage/eye irritation:
Causes serious eye irritation (H319).
Respiratory or skin sensitization:
May cause an allergic skin reaction (H317).
Germ cell mutagenicity:
No data available.
Carcinogenicity:
No data available.
Reproductive toxicity:
Suspected of damaging fertility or the unborn child (H361).
Specific target organ toxicity (single exposure):
No data available.
Specific target organ toxicity (repeated exposure):
No data available.
Aspiration hazard:
No data available.

11.2 Additional information
Carcinogen classification:
2-Hydroxy-4-methoxybenzophenone
TR-597: Toxicology and Carcinogenesis Studies of 2-Hydroxy-4- methoxybenzophenone (CASRN 131-57-7) Administered in Feed to Sprague Dawley (Hsd:Sprague Dawley SD) Rats and B6C3F1/N Mice (2020 )
12/12/19
Equivocal Evidence
Equivocal Evidence
No Evidence
No Evidence
Under the conditions of these 2-year studies, there was equivocal evidence of carcinogenic activity of 2H4MBP exposure in male Hsd:Sprague Dawley SD rats based on the occurrence of malignant meningiomas
Data source: Hazardous Substances Data Bank (HSDB) via PubChem.

12.1 Toxicity
EC50; Species: Isochrysis galbana (Haptophyte) exponential growth phase, 7000 cells/mL; Conditions: saltwater, static, 20 °C, pH 8; Concentration: 13.87 ug/L for 72 hr (95% confidence interval: 0-41.69 ug/L); Effect: decreased population growth rate /formulation/
LC50; Species: Acropora cervicornis (Staghorn Coral ) larva; Conditions: saltwater, static, 22 °C; Concentration: 9 ug/L for 4 hr (95% confidence interval: 5.4-14.5 ug/L) /formulation/
EC50; Species: Mytilus galloprovincialis (Mediterranean Mussel) egg; Conditions: saltwater, static, 20 °C; Concentration: 3472.59 ug/L for 48 hr (95% confidence interval: 3359.65-3585.52 ug/L); Effect: decreased normal development /formulation/
LC50; Species: Dugesia japonica (Flatworm) body length 0.7 cm; Conditions: fresh, static, 25 °C; Concentration: 2200 ug/L for 24 hr />99% purity/
For more Ecotoxicity Values (Complete) data for 2-Hydroxy-4-methoxybenzophenone (7 total), please visit the HSDB record page.
/AQUATIC SPECIES/ Benzophenone-3 (BP-3) is a widely used organic UV-filter compound. Despite the frequent occurrence of BP-3 in aquatic environments, little is known about its effect on fish behavior. The aim of this study was to investigate the endocrine disrupting effects of BP-3 in male fighting fish (Betta splendens) with a focus on agonistic behavior. Male fighting fish were exposed to 10, 100, and 1000 ug/L BP-3, as well as a solvent control (0.1% ethanol) and a positive control (100 ng/L 17alpha-ethynylestradiol, EE2), fo

12.2 Persistence and degradability
No data available.

12.3 Bioaccumulative potential
Log P (n-octanol/water): 3.6
Potential for bioaccumulation exists (Log P > 3).

12.4 Mobility in soil
No data available.

12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available.

12.6 Other adverse effects
This substance is classified as hazardous to the aquatic environment.

13.1 Waste treatment methods
Waste Treatment Methods: Waste material must be disposed of in accordance with national and local regulations. Leave chemicals in original containers and do not mix with other waste. Handle uncleaned containers in the same manner as the product itself.

14.1 UN number
Not regulated as dangerous goods (research quantities typically exempt).

14.2 UN proper shipping name
Not subject to transport regulations (small quantities for research use).

14.3 Transport hazard class(es)
Not classified as dangerous goods for transport (research quantities).

14.4 Packing group
Not applicable (not regulated as dangerous goods in typical research quantities).

14.5 Environmental hazards
Marine pollutant: Yes (classified as environmentally hazardous per GHS).

14.6 Special precautions for user
Transport in original packaging. Ensure containers are tightly sealed.
For bulk or commercial quantities, consult applicable transport regulations (DOT, IATA, IMDG).

14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable.

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
US EPA / TSCA: Subject to EPA TSCA regulations
EU ECHA / REACH: Registered (REACH Active)

SARA 302 Components:
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313 Components:
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SARA 311/312 Hazards:
Acute (short-term) health hazard
Chronic (long-term) health hazard
Environmental hazard

Massachusetts Right To Know Components:
This material contains components subject to the Massachusetts Right to Know Act. See Section 2 for hazard classification.
Pennsylvania Right To Know Components:
This material contains components subject to the Pennsylvania Right to Know Act. See Section 2 for hazard classification.
New Jersey Right To Know Components:
This material contains components subject to the New Jersey Right to Know Act. See Section 2 for hazard classification.

California Prop. 65 Components:
This product does not contain any chemicals known to the State of California to cause cancer, birth defects, or any other reproductive harm.

Other regulatory listings:
- The Australian Inventory of Industrial Chemicals: Chemical: Methanone, (2-hydroxy-4-methoxyphenyl)phenyl-
- TSCA Requirements: Section 8(a) of TSCA requires manufacturers of this chemical substance to report preliminary assessment information concerned with production, exposure, and use to EPA as cited in the preamble in 51 FR 41329. Effective date: September 29, 2006; Reporting date: November 28, 2006.
Pursuant to section
- FDA Requirements: The Approved Drug Products with Therapeutic Equivalence Evaluations identifies currently marketed over-the-counter drug products, including oxybenzone, approved on the basis of safety and effectiveness by FDA under sections 505 of the Federal Food, Drug, and Cosmetic Act.
Sunscreen active ingredient

15.2 Chemical safety assessment
A chemical safety assessment has not been carried out for this substance.
For research-use-only compounds, no CSA is required under REACH Annex I.

Revision Date: 2026/09/09
Further Information: The information provided is believed to be correct but is not exhaustive and should be used only as a guideline based on current knowledge. It does not represent a guarantee of the properties of the product. Selleck Chemicals Corporation and its Affiliates shall not be held liable for any damage resulting from handling or contact with the product.