Download SDS
CAS No.: 88-99-3
Check the Phthalic acid product page for in-depth specifications, including solubility, stock solutions, MOA, and working concentrations.

Quick Safety Reference

🛡️ Hazard Overview

  • GHS Class: GHS05; GHS07; GHS08
  • Signal Word: Danger
  • Hazard Statements: H315; H318; H319; H335; H360D

🧤 PPE Guidelines

  • Gloves: Chemical‑resistant gloves suggested
  • Eye Protection: Safety goggles suggested
  • Respirator: Dust respirator if dust occurs

❄️ Storage

  • Storage Temp: -20°C (-4°F) Keep dry

🚑 Emergency First Aid

  • For inhalation, skin, eye or ingestion exposure, please refer to full SDS Section 4.

GHS 16 Safety Standard Sections

Product identifier

  • Product Name: Phthalic acid
  • Catalog Number: S6215
  • CAS Number: 88-99-3
  • IUPAC Name: 1,​2-​Benzenedicarboxylic acid

Relevant identified uses and uses advised against

  • Identified uses: For research and development use only; laboratory chemicals; manufacture of substances.
  • Uses advised against: Not for pharmaceutical, household, or other unapproved uses.

Details of the supplier

  • Company: Selleck Chemicals
  • TollFree: +1 877 796-6397
  • Tel: +1 832 582-8158
  • Fax: +1 832 582-8590

Emergency telephone number

  • Emergency phone #: +1 832 582-8158

2.1 GHS classification in accordance with 29 CFR 1910 (OSHA HCS):
Skin irritation: Category 2. H315
Serious eye damage: Category 1. H318
Serious eye irritation: Category 2. H319
Specific target organ toxicity (single exposure): Category 3. H335
Not classified. H360D

2.2 GHS Label elements, including precautionary statements
Hazard Pictogram(s):
GHS05 GHS07 GHS08
Signal Word:
Danger
Hazard statement(s):
H315: Causes skin irritation
H318: Causes serious eye damage
H319: Causes serious eye irritation
H335: May cause respiratory irritation
H360D: May damage the unborn child
Precautionary statement(s):
Prevention:
P203: Obtain, read and follow all safety instructions before use.
P261: Avoid breathing dust/fume/gas/mist/vapors/spray.
P264: Wash hands thoroughly after handling.
P264+P265: Wash hands thoroughly after handling. Do not touch eyes.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection/hearing protection.
Response:
P302+P352: IF ON SKIN: wash with plenty of water.
P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305+P351: IF IN EYES: Rinse cautiously with water for several minutes.
P305+P354: IF IN EYES: Immediately rinse with water for several minutes.
P317: Get emergency medical help.
P318: if exposed or concerned, get medical advice.
P319: Get medical help if you feel unwell.
P321: Specific treatment (see information on this label and safety datasheet)).
P332+P317: If skin irritation occurs: Get medical help.
P337+P317: If eye irritation persists: Get medical help.
P338: Remove contact lenses, if present and easy to do. Continue rinsing.
P362+P364: Take off contaminated clothing and wash it before reuse.
Storage:
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P405: Store locked up.
Disposal:
P501: P501 Dispose of contents/ container to an approved waste disposal plant.

2.3 Other hazards
None.

3.1 Substances
Product name: Phthalic acid
CAS Number: 88-99-3
PubChem CID: 1017
Molecular formula: C8H6O4
Molecular weight: 166.13 g/mol
IUPAC name: phthalic acid

3.2 Mixtures
Not applicable (pure substance).

4.1 Description of first aid measures
Inhalation: Fresh air, rest.
Skin contact: Rinse and then wash skin with water and soap.
Eye contact: Rinse with plenty of water for several minutes (remove contact lenses if easily possible).
Ingestion: Rinse mouth.

4.2 Most important symptoms and effects, both acute and delayed
See Section 11 (Toxicological Information).

4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically. Contact a poison control center or physician for severe exposure.

5.1 Extinguishing media
Suitable: Water spray, dry chemical, carbon dioxide (CO2), alcohol-resistant foam.
Unsuitable: None known.

5.2 Specific hazards arising from the substance or mixture
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. (NTP, 1992)
Use water spray, powder, alcohol-resistant foam, carbon dioxide.
Powder, water spray, foam, carbon dioxide.
Evaporation at 20 °C is negligible; a nuisance-causing concentration of airborne particles can, however, be reached quickly.

5.3 Advice for firefighters
Wear self-contained breathing apparatus (SCBA) and full protective clothing.
Fight fire from upwind. Cool containers with water spray until fire is extinguished.
Flash point: 334 °F (NTP, 1992)

6.1 Personal precautions, protective equipment and emergency procedures
Wear appropriate personal protective equipment (see Section 8).
Avoid breathing dust/vapor. Ensure adequate ventilation.
Evacuate personnel to safe areas. Keep people away from and upwind of spill.

6.2 Environmental precautions
Prevent product from entering drains, waterways, or soil.
Contain spill with inert absorbent material.

6.3 Methods and materials for containment and cleaning up
Personal protection: particulate filter respirator adapted to the airborne concentration of the substance. Sweep spilled substance into covered containers. If appropriate, moisten first to prevent dusting. Wash away remainder with plenty of water.
Sweep spilled substance into containers; if appropriate, moisten first to prevent dusting (extra personal protection: P1 filter respirator for inert particles).
SRP: The most favorable course of action is to use an alternative chemical product with less inherent propensity for occupational exposure or environmental contamination. Recycle any unused portion of the material for its approved use or return it to the manufacturer or supplier. Ultimate disposal of the chemical must consider: the material's impact on air quality; potential migration in soil or water; effects on animal, aquatic, and plant life; and conformance with environmental and public health regulations.
Good local & general ventilation are required where phthalic acid is handled.
SRP: Local exhaust ventilation should be applied wherever there is an incidence of point source emissions or dispersion of regulated contaminants in the work area. Ventilation control of the contaminant as close to its point of generation is both the most economical and safest method to minimize personnel exposure to airborne contaminants.
NO open flames ... Prevent deposition of dust; closed system, dust explosion-proof electrical equipment and lighting ... PREVENT DISPERSION OF DUST ... Do not eat, drink, or smoke during work.

7.1 Precautions for safe handling
SMALL SPILLS AND LEAKAGE: Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONS: You should store this chemical under ambient temperatures, and keep it away from oxidizing materials. (NTP, 1992)

7.2 Conditions for safe storage, including any incompatibilities
Store in a cool, dry, well-ventilated area. Keep container tightly closed.
Store away from incompatible materials (see Section 10).
Protect from light and moisture.
Recommended storage (industry convention for research compounds): -20°C for long-term storage; 2-8°C for short-term use and transport.
[Note: This is a general industry recommendation. Always verify exact storage conditions with the supplier Certificate of Analysis (COA).]

8.1 Exposure controls
8.1.1 Occupational exposure limits (OEL)
OSHA PEL: Not established.
ACGIH TLV: Not established.
NIOSH REL: Not established.
No occupational exposure limit values are established for this substance.
Use the lowest feasible exposure level (ALARA principle).

8.1.2 Appropriate engineering controls
Use only in a chemical fume hood or with local exhaust ventilation.
Ensure adequate ventilation to keep airborne concentrations below exposure limits.

8.2 Individual protection measures
8.2.1 Eye/face protection
Wear chemical safety goggles and face shield.
8.2.2 Skin protection
Wear protective gloves. Recommended material: Nitrile rubber.
Wear suitable protective clothing (lab coat).
8.2.3 Respiratory protection
Use NIOSH-approved dust/mist respirator (N95 or higher) if ventilation is inadequate.
8.2.4 Thermal hazards
Not applicable.

9.1 Information on basic physical and chemical properties
a) Appearance: Phthalic acid appears as white crystals or fine white powder. (NTP, 1992)
b) Odor: No data available
c) Odor threshold: No data available
d) pH: No data available
e) Melting point/freezing point: 410 to 412 °F (decomposes) (NTP, 1992)
f) Initial boiling point and boiling range: Decomposes (NTP, 1992)
g) Flash point: 334 °F (NTP, 1992)
h) Evaporation rate: No data available
i) Flammability (solid, gas): No data available
j) Upper/lower flammability or explosive limits: No data available
k) Vapor pressure: 0.00000064 [mmHg]
l) Vapor density: No data available
m) Relative density: 1.593 at 68 °F (NTP, 1992) - Denser than water; will sink
n) Water solubility: less than 1 mg/mL at 68 °F (NTP, 1992)
o) Partition coefficient: n-octanol/water: Log P (n-octanol/water): 0.7
p) Auto-ignition temperature: No data available
q) Decomposition temperature: No data available
r) Viscosity: No data available
s) Explosive properties: No data available
t) Oxidizing properties: No data available

9.2 Other information
Topological Polar Surface Area (TPSA): 74.6 Ų
Complexity: 177

10.1 Reactivity
No specific reactivity hazards identified under normal handling conditions.

10.2 Chemical stability
Stable under recommended storage conditions.

10.3 Possibility of hazardous reactions
No hazardous reactions under normal conditions.

10.4 Conditions to avoid
Avoid heat, sparks, open flames, direct sunlight, and moisture.

10.5 Incompatible materials
Mixtures of sodium nitrite and phthalic acid or phthalic anhydride explode violently on heating. A nitrite ester may have been produced.
The exothermic nitration of phthalic acid or phthalic anhydride by a fuming nitric acid-sulfuric acid mixture may give mixtures of the potentially explosive phthaloyl nitrates or nitrites or their nitro derivatives. Formation of these cmpd may be avoided if nitrating mixture is extensively diluted with sulfuric acid and if a small (1.5 mole equiv) /amount/ of nitric acid is present.

10.6 Hazardous decomposition products
Thermal decomposition may produce: Carbon monoxide (CO), Carbon dioxide (CO₂).
See also Section 5 (Fire-fighting measures) for combustion products.

11.1 Information on toxicological effects
Acute toxicity:
No acute toxicity data available.
Skin corrosion/irritation:
Causes skin irritation (H315).
Serious eye damage/eye irritation:
Causes serious eye damage (H318).
Respiratory or skin sensitization:
No data available.
Germ cell mutagenicity:
No data available.
Carcinogenicity:
No data available.
Reproductive toxicity:
No data available.
Specific target organ toxicity (single exposure):
No data available.
Specific target organ toxicity (repeated exposure):
No data available.
Aspiration hazard:
No data available.

11.2 Additional information
Signs and symptoms of exposure:
Cough. Sore throat.
Redness.
Redness.
Sore throat.
Data source: Hazardous Substances Data Bank (HSDB) via PubChem.

12.1 Toxicity
LC50; Species: Bufo bufo japonicus (Toad); Conditions: freshwater; static; Concentration: 36000 ug/L for 24 hr at 25 °C, pH 5.0 /formulated product/
LC50; Species: Bufo bufo japonicus (Toad); Conditions: freshwater; static; Concentration: >40000 ug/L for 24 hr at 25 °C, pH 6.0 /formulated product/
LC50; Species: Bufo bufo japonicus (Toad); Conditions: freshwater; static; Concentration: >40000 ug/L for 24 hr at 25 °C, pH 7.0 /formulated product/
LC50; Species: Bufo bufo japonicus (Toad); Conditions: freshwater; static; Concentration: >40000 ug/L for 24 hr at 25 °C, pH 8.0 /formulated product/
For more Ecotoxicity Values (Complete) data for PHTHALIC ACID (10 total), please visit the HSDB record page.
Phthalic acid's use in the production of dyes, phenolphthalein, phthalimide, anthranilic acid, synthetic perfumes and laboratory reagents may result in its release to the environment through various waste streams. If released to air, a vapor pressure of 6.36X10-7 mm Hg at 25 °C indicates phthalic acid will exist in both the vapor and particulate phases in the atmosphere. Vapor-phase phthalic acid will be degraded in the atmosphere by reaction with photochemically-produced hydroxyl radicals; the half-life for this reaction in air is estimated to be 13 days. Particulate-phase phthalic acid will be removed from the atmosphere by wet or dry deposition. Due to its high water solubility and polar nature, phthalic acid is associated with water droplets in the atmosphere and effectively s

12.2 Persistence and degradability
No data available.

12.3 Bioaccumulative potential
Log P (n-octanol/water): 0.7
Low potential for bioaccumulation (Log P < 3).

12.4 Mobility in soil
No data available.

12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available.

12.6 Other adverse effects
No other adverse ecological effects identified.

13.1 Waste treatment methods
Waste Treatment Methods: Waste material must be disposed of in accordance with national and local regulations. Leave chemicals in original containers and do not mix with other waste. Handle uncleaned containers in the same manner as the product itself.

14.1 UN number
Not regulated as dangerous goods (research quantities typically exempt).

14.2 UN proper shipping name
Not subject to transport regulations (small quantities for research use).

14.3 Transport hazard class(es)
Not classified as dangerous goods for transport (research quantities).

14.4 Packing group
Not applicable (not regulated as dangerous goods in typical research quantities).

14.5 Environmental hazards
Marine pollutant: No (not classified as environmentally hazardous per GHS).

14.6 Special precautions for user
Transport in original packaging. Ensure containers are tightly sealed.
For bulk or commercial quantities, consult applicable transport regulations (DOT, IATA, IMDG).

14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable.

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
US EPA / TSCA: Subject to EPA TSCA regulations
EU ECHA / REACH: Registered (REACH Active)

SARA 302 Components:
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313 Components:
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SARA 311/312 Hazards:
Acute (short-term) health hazard

Massachusetts Right To Know Components:
This material contains components subject to the Massachusetts Right to Know Act. See Section 2 for hazard classification.
Pennsylvania Right To Know Components:
This material contains components subject to the Pennsylvania Right to Know Act. See Section 2 for hazard classification.
New Jersey Right To Know Components:
This material contains components subject to the New Jersey Right to Know Act. See Section 2 for hazard classification.

California Prop. 65 Components:
This product does not contain any chemicals known to the State of California to cause cancer, birth defects, or any other reproductive harm.

Other regulatory listings:
- The Australian Inventory of Industrial Chemicals: Chemical: 1,2-Benzenedicarboxylic acid
- EFSA Legal Basis: Regulation (EC) No 1107/2009 (amended)
- FDA Requirements: o-Phthalic acid is an indirect food additive for use as a component of adhesives.

15.2 Chemical safety assessment
A chemical safety assessment has not been carried out for this substance.
For research-use-only compounds, no CSA is required under REACH Annex I.

Revision Date: 2026/09/09
Further Information: The information provided is believed to be correct but is not exhaustive and should be used only as a guideline based on current knowledge. It does not represent a guarantee of the properties of the product. Selleck Chemicals Corporation and its Affiliates shall not be held liable for any damage resulting from handling or contact with the product.

Note: Technical data last updated: Sep 1, 2026.