ATF4 Rabbit Recombinant mAb | Monoclonal Antibodies

ATF4 Rabbit Recombinant mAb

Catalog No.A5514

For research use only.

Cited by 1 Publication

Advantages

1. Why choose rabbit monoclonal antibody?
Rabbit monoclonal antibody has over 100 times higher affinity than that of mouse monoclonal.

2.Why choose recombinant antibodies?
Recombinant antibodies are known for higher purity and minimal deviation between batches, versus regular antibodies.

Application Data

WB

Validated by Selleck

IF

Validated by Selleck

Usage Information

Application WB, IF,ELISA
Dilution
WB IF
1:1000 1:50
Reactivity Human Mouse Rat
MW (kDa) 50kDa
Source Rabbit
Concentration 1mg/ml
Storage buffer 10 mM sodium HEPES (pH 7.5), 150 mM NaCl, 100 µg/ml BSA, 50% glycerol and less than 0.02% sodium azide.
Storage Store at –20°C.

Protocol

WB

Western Blotting

Sample preparation

1. Aspirate media from cultures and Wash the cells with 1X PBS.
2. Lyse cells by adding 1X SDS sample buffer and transfer the extract to a microcentrifuge tube. Keep onice.
3. Sonicate for 10–15 sec to complete cell lysis and shear DNA.
4. Heat a 20 µl sample to 95–100°C for 5 min, then cool on ice.
5. Centrifuge for 5 min (with Microcentrifuge).
6. Load appropriate volumes of samples onto SDS-PAGE gel (loading quantity of protein sample depends on the concentration of extracted proteins).
NOTE: At the same time, please load the pre-stained molecular weight markers to determine molecular weights and verify electrotransfer.
7. Electrotransfer to nitrocellulose/PVDF membrane.

Membrane Blocking and Antibody Incubations

a. Blocking

1. (Optional) After transfer, wash the transferred membrane with TBS for 5 min at room temperature.
2. Incubate the membrane in the blocking buffer for 1 hr at room temperature.
3. Wash three times for 5 min each with TBST.

b. Antibodies Incubation

1. Incubate membrane and primary antibody (at the appropriate dilution and diluent recommended) in a primary antibody dilution buffer with gentle agitation overnight at 4°C.
2. Wash three times for 5 min each with TBST.
3. Incubate membrane with an appropriate second antibodydissolved in the blocking buffer with gentle agitation for 1 hr at room temperature.
4. Wash three times for 5 min each with TBST.
5. Proceed with detection.

Detection of Proteins

1. After antibodies incubation, Wash membrane three times for 5 minutes in TBST.
2. PrepareECL Reagent (or other chromogenic agents/substrate according to your second antibody). Mix well.
3. Incubate substrate with membrane for 1 minute, remove excess solution (membrane remains wet), wrap in plastic and expose to X-ray film.

IF

Immunofluorescence (Immunocytochemistry)

Specimen Preparation (forcultured cell lines, IF-IC)

1. Aspirate liquid, then cover cells to a depth of 2–3 mm with 4% formaldehyde diluted in 1X PBS.
NOTE: Formaldehyde is toxic, use only in a fume hood.
2. Fix cells for 15 min at room temperature.
3. Aspirate fixative, rinse three times in 1X PBS for 5 min each.
4. Proceed with Immunostaining.

Immunostaining

1. Add theblocking buffer and incubate for 60 min at RT.
2. Prepare primary antibody diluent in antibody dilution buffer as recommended .
3. Aspirate blocking solution, apply diluted primary antibody.
4. Incubate overnight at 4°C.
5. Rinse three times in 1X PBS for 5 min each.
6. Incubate specimens in fluorochrome-conjugated secondary antibody diluted in antibody dilution buffer for 1–2 hr at room temperature in the dark.
7. Rinse three times in 1X PBS for 5 min each.
8. Mount slides usingmounting medium with DAPI and cover with coverslips.
9. For best results, allow mountant to cure overnight at room temperature. For long-term storage, store slides flat at 4°C protected from light.

Description

Specificity ATF4 Rabbit Recombinant mAb detects endogenous level of total ATF4.
Background Activating transcription factor 4 (ATF4), a member of the ATF/CREB transcription factor family, is an important factor that participates in several pathophysiological processes such as the stress response, bone resorption, medullary hematopoiesis and lens formation. It forms homodimers and heterodimers with other transcription factors, including some members of the AP-1 family. ATF4 acts as a transcription activator and inhibitor. Its activity is primarily regulated at the post-transcriptionally level, especially the translation of ATF4 mRNA. The protein degrades quickly, and its half-life is only 30-60 min.

Datasheet & SDS

Tech Support

If you have any other enquiries, please leave a message.

* Indicates a Required Field

Please enter your name.
Please enter your email. Please enter a valid email address.
Please write something to us.